If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
I have an off lease unit that was refurbished and installed last week and has about 250 k combined prints. Everything on the unit functions and works as it should except color printing and copying from tray one only. It prints anything in color from tray one very slowly. It has about a 3 second wait in between each color page during each print. It always prints perfectly with no jams but it's about 10 prints per minute rather than 60. However, black prints works from tray 1 at 60 prints per minute. No issues with black and white out of tray one only color. Paper tray two works perfect on every function as it should and the correct speed.
Internal prints from tray 1 have the same symptom. Black and white works at the correct speed but color is slow.
It's almost as if it's trying to run a very high quality print from tray one only or it's trying to spool up the image. These are not large PDFs by any means I've tried several different file types and sizes. I have compared all media types outputs and sizes for the two trays and they are all the same that I can find. There's never any adding toner or auto calibration in progress message on the display.
Firmware was updated. I have temporarily disabled tray one and made tray two their default until I find a solution.
Any ideas or suggestions are greatly appreciated. It's still really feels like a setting issue but I can't find one.
Best rule for troubleshooting.
K I S S Keep It Simple Stupid
I have an off lease unit that was refurbished and installed last week and has about 250 k combined prints. Everything on the unit functions and works as it should except color printing and copying from tray one only. It prints anything in color from tray one very slowly. It has about a 3 second wait in between each color page during each print. It always prints perfectly with no jams but it's about 10 prints per minute rather than 60. However, black prints works from tray 1 at 60 prints per minute. No issues with black and white out of tray one only color. Paper tray two works perfect on every function as it should and the correct speed.
Internal prints from tray 1 have the same symptom. Black and white works at the correct speed but color is slow.
It's almost as if it's trying to run a very high quality print from tray one only or it's trying to spool up the image. These are not large PDFs by any means I've tried several different file types and sizes. I have compared all media types outputs and sizes for the two trays and they are all the same that I can find. There's never any adding toner or auto calibration in progress message on the display.
Firmware was updated. I have temporarily disabled tray one and made tray two their default until I find a solution.
Any ideas or suggestions are greatly appreciated. It's still really feels like a setting issue but I can't find one.
First things first. Did you push a clone on to the machine?
No I did not clone any machine, however, I'm not sure what was done with the machine before we got it. I missed on my checklist to do a factory reset which is my next step, but I did not want to do it during the busy work day as the customer relies heavily on this model.
It does act as though tray one is set to heavy paper or labels, but I double checked that both trays are set to plain 1 paper. Every setting I could find are identical from tray to tray. Also, if the media was set differently for tray 1, it would do it for black also not just color.
Best rule for troubleshooting.
K I S S Keep It Simple Stupid
No I did not clone any machine, however, I'm not sure what was done with the machine before we got it. I missed on my checklist to do a factory reset which is my next step, but I did not want to do it during the busy work day as the customer relies heavily on this model.
It does act as though tray one is set to heavy paper or labels, but I double checked that both trays are set to plain 1 paper. Every setting I could find are identical from tray to tray. Also, if the media was set differently for tray 1, it would do it for black also not just color.
Could try backing up the system settings, resetting them back to factory defaults, and see what happens. That's a 3 minute check you could do with the network unplugged so print jobs don't mess anything up.
I've seen weird issues with tray 1 after being cloned from a machine that didn't have auto-select in tray 1(ended up jamming though settings were correct), so you could try changing the paper type and size to something else, submitting the change, then revert back to what you want.
If you don't know if it was cloned previously, as in someone else may have cloned it but not your company, I would always assume it's a strong possibility. The '71 series began the problems we had with slow output issues, but we could never recreate it, but we may not have been printing color... That's also why we don't clone anything anymore, Sharp's are too finicky now.
dumb suggestion, but have you changed the orientation of the paper in tray 1 and tested it? I had a similar issue with a diff model I just had to changed it from long to short or vice versa.
A4 Prints and copies slowly from Tray one. All other trays OK and A4R and A3 are Ok too. Mono Black and white prints fine. paper exits the machine and there is a delay before the next sheet exits.
There is a delay in the paper reaching the Reg (paper Stop) unit which causes the machine to have to clean the transfer unit and re-make the image.
This delay slows the machine down. Please fit new Tray one paper feed unit to rectify this issue.
A favorite resort of the foreign residents of Yokohama during the summer months is the island of Enoshima. It is about twenty miles away, and is a noted place of pilgrimage for the Japanese, on account of certain shrines that are reputed to have a sacred character. Doctor Bronson arranged that his party should pay a visit to this island, as it was an interesting spot, and they could have a glimpse of Japanese life in the rural districts, and among the fishermen of the coast. "But as we are in for it," he continued, "we must make the best of the situation, and hope to go through in safety. Many a strong ship lies at the bottom of the sea, where she was sent by just such a storm as we are about to pass through, and many another has barely escaped. I was once on a ship in the China seas, when the captain told the passengers that it would be a miracle if we remained half an hour longer afloat. But hardly had he done speaking when the wind fell, the storm abated, and we were safe. The typhoon is to these waters what the hurricane is to the West Indies; it is liable to blow at any time between April and September, and is often fearfully destructive. OPIUM-PIPE. OPIUM-PIPE. "Surely your ladyship knows Dr. Bruce!" Hetty said with a vivid splash of colour on either cheek "A little time ago I understood that Dr. Bruce----" "I require that everywhere a strict investigation shall take place into the conduct of the soldiers with regard to the life and property of the civilian population. "Where were they buried?" They all pressed forward. "Count out. That's the only fair way," shouted the boys in the center. "Now, there's three loaves o' bread for the Sargint," said Harry, laying them down on a newspaper. "There's three for the Corpril; there's three for me; there's three for you." "'T?un't peas, thick 'un," Vennal would break in uproariously, "it's turnips—each of 'em got a root like my fist." At this moment of perplexity, some medicine, that she had obtained from Edith, occurred to her, and, with a feeling of confidence, and almost of extacy, she took a phial from a shelf in a cupboard where she had placed it, and, pouring out the contents in a large spoon, hesitated an instant ere she administered it. "Let me see," said she; "surely it was a large spoonful Edith told me to give—yet all that was in the phial doesn't fill the spoon. Surely I can't be wrong: no—I remember she said a large spoonful, and we didn't talk of any thing else—so I must be right." But Mary still hesitated, till, hearing a sudden noise in the court-yard, which, she conjectured, was her mistress returned, and as the child was getting worse every moment, she leaned back its head, and, forcing open its mouth, compelled the patient, though with difficulty, to swallow its death. The draught was taken; the rigid muscles relaxed, and for a minute the child lay motionless in her lap; but in an instant after, Mary could scarcely suppress a shriek at the horrid sight that met her gaze. The eyes opened, and glared, and seemed as if starting from the head—the fair face and the red lips, were blue, deepening and deepening, till settling in blackness—the limbs contracted—the mouth opened, and displayed a tongue discoloured and swollen—then came a writhing and heaving of the body, and a low, agonized moan: and, as Mary looked almost frantic at this dreadful sight, Edith's words, when she had given her the phial, "that there was enough there to kill," suddenly occurred to her—and then, too, came, with a dreadful distinctness, the remembrance of the true directions which Edith had given. It was nearly noon the next day, when the under-sheriff entered the room to ask if their opinions were yet unanimous. The galleyman still refused. "That for ye, coward," said Tyler, striking him with the flat side of his bared weapon. Oakley aimed another thrust which was again turned aside, and the smith, now flinging down his sword, seized upon his right hand and wrenched the dagger from its grasp. After a short struggle, Oakley fell heavily on the pavement with the blood streaming from his mouth and nostrils. HoME萝拉泷泽第4部资源
ENTER NUMBET 0016fismall.net.cn www.lz1zb.net.cn kgchain.com.cn jlchain.com.cn eotsge.com.cn www.jwjips.com.cn www.pbmdcb.com.cn www.ricpsd.com.cn www.shuimozi.com.cn x-moxing.com.cn
Comment